Jet Tools JBTS-10MJS Instrukcja Użytkownika

Operating Instructions and Parts Manual 10" Job Site Table Saw Benchtop Series – Model No. JBTS-10MJS WALTER MEIER (Manufacturing) Inc.

10Shipping Contents Unpacking 1. Remove the contents from the shipping container. 2. Compare the contents of the shipping container and hardware bags

11 Figure 4 – Hardware Hardware The following items are shown in Figure 4. Q Screw (2) R Collar (4) S Shaft Sleeve (2) T Nut (2) U Screw (1) V Nut

12Assembly Note: The letter designators used in the assembly section are the same as those used in the shipping contents and hardware section (page 1

13Mounting the Saw to Work Surface A hole to allow sawdust to fall through must be provided when the saw is mounted to a work surface (stand not use

14Handwheel Handle Thread the handwheel handle (DD, Fig. 10) into the handwheel hole (A. Fig. 10), and then tighten the nut against the handwheel wit

15Blade Guard Assembly To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the p

16Installing the Push-stick Storage Attach the metal push-stick storage bracket (Figure 13) into the provided slot (D, Fig. 14) on the right side of

17Adjustments Setting up the Stand Referring to Figure 16: 1. Release the stand lock hook (D) by sliding it away from the stop screw. 2. Raise the ha

18Aligning the Blade Guard Splitter To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnect

1990° and 45° Positive Stop Adjustment Adjusting the Positive Stop Your saw has positive stops that will quickly position the saw blade at 90° and 45

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au

20Blade Parallel to the Miter Slot To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnecte

21Adjusting the Miter Gauge Referring to Figure 24: 1. Loosen the lock handle (B) to allow the miter body (C) to rotate freely. Position the miter bo

22Rip Fence Indicator The rip fence indicator points to the scale on the front of the table saw. The measurement shown by the indicator will provide

23Operation Basic Saw Operations Raising the Blade To raise or lower the blade, turn the blade elevation handwheel (A, Fig. 30) to the desired blade

24 Figure 33 Cutting Operations There are two basic types of cuts: ripping and crosscutting. Ripping is cutting along the length and the grain of the

25stops, raise the anti-kickback pawls (A) on each side of the splitter and slide the workpiece out. Figure 35 Bevel Ripping This cut is the same a

26interfere with the cut if used on the left side groove. Referring to Figure 38: 1. Adjust the blade (A) to the desired angle, and tighten the blade

271. Remove the saw blade and the blade guard for dado cuts ONLY. Reinstall and realign blade guard for all through- sawing operations. Install a da

28Maintenance General Maintenance For your own safety, turn the switch OFF and remove the switch key. Remove the plug from the power source outlet

29 Figure 44 5. Referring to Figure 45: 6. Remove the black plastic cap (B) from the side of the motor (C). 7. Carefully remove the spring-loaded

Table of Contents Warranty and Service...

Troubleshooting Trouble Probable Cause Remedy Saw will not start. 1. Saw is not plugged in. 2. Fuse blown or circuit breaker tripped. 3. Cord is

31Parts Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848, Monday through Friday (see our website for bu

32Table Saw Index No. Part No. Description Size Qty 48 ... ...Spring Pin ...

33Table Saw Index No. Part No. Description Size Qty 105 ... JBTS10MJS-105...End Cap...

34Table Saw Index No. Part No. Description Size Qty 162 ... JBTS10MJS-162...Support Leg ...

35Table Saw Index No. Part No. Description Size Qty 219 ... ...Miter Bar ...

36Table Saw

37

38Mobile Stand Index No. Part No. Description Size Qty 1 ... JBTS10MJS-601...Carriage Bolt ...

39Mobile Stand Index No. Part No. Description Size Qty 58 ... JBTS10MJS-658...Bumper ...

4 Warnings 1. Read and understand the entire owners' manual before attempting assembly or operation. 2. Read and understand the warnings post

40Wiring Diagram WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6

5 20. Don't use in dangerous environment. Don't use power tools in damp or wet locations, or expose them to rain. Keep work area well ligh

6 Table Saw Safety 1. Always use a saw blade guard, splitter and anti-kickback pawls for every through–sawing operation. Through–sawing operations a

7 Specifications Stock Number ...

8 Electrical Grounding Instructions In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to

9 Features Figure 1 – Features