Jet Tools 10-inch Instrukcja Użytkownika

Operating Instructions and Parts Manual 10-inch Table Saw Model JPS-10TS shown with optional mobile base #708119 (not provided) WALTER ME

10Assembly Read and understand all assembly instructions before attempting assembly! Failure to comply may cause serious injury! Unpacking and Clea

113. Slide the remaining handwheel (E) with the smaller mounting hole onto the shaft (F) on the right side of the table saw, lining up the flat sid

12Blade Guard and Splitter Referring to Figure 12: 1. Through the saw table opening on top, locate two hex nuts (A1) that secure two retaining plate

13If alignment is required: 3. Move the straight-edge aside and through the opening (see inset) locate four hex nuts (F, G) and two retaining plates

14Grounding Instructions 1. All Grounded, Cord-connected Tools: In the event of a malfunction or breakdown, grounding provides a path of least resist

15Extension Cord Recommendations USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure

16Adjustments Disconnect saw from power source before making adjustments. Blade Raising and Tilt Mechanism Never try to force the tilting mechanism

17If adjustment is required: 10. Back out the 45º adjust setscrew (turn counterclockwise) one or two turns with a 4mm hex wrench (F, Fig. 20). 11. Tu

18Operations (NOTE: The following Figures may or may not show your specific saw, but the procedures are the same.) Table Saws Familiarize yourself wi

19Rip Sawing Ripping is where the work piece is fed with the grain into the saw blade using the fence as a guide and a positioning device to ensure t

2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au

20When ripping long boards, use a support at the front of the table, such as a roller stand, and a support or "tailman" at the rear as show

21To improve the effectiveness of the miter gauge in crosscutting, some users mount an auxiliary wooden extension face (with a glued-on strip of sand

22These include push sticks, feather boards, filler pieces, fixtures, jigs and any other appropriate device that can be utilized to keep operator&apo

23Figure 39 – Push Stick Template Maintenance Always disconnect power to the machine before performing maintenance. Failure to do this may resu

24Troubleshooting Symptom Possible Cause Correction Motor will not start Low voltage. Check power line for proper voltage. Open circuit in motor o

25Motor and Trunnion Index No Part No Description Size Qty 1 ... VB-A31 ...Belt ...

26Motor and Trunnion Index No Part No Description Size Qty 55 ... JWTS10-155 ...Wave Washer...

27Motor and Trunnion

28Table and Cabinet Index No Part No Description Size Qty 1 ... JPS10TS-301 ...Table ...

29Table and Cabinet Index No Part No Description Size Qty 56 ... TS-1533042 ...Pan Head Screw...

3 Table of Contents Table of Contents ...

30Stand Assembly Index No Part No Description Size Qty 1 ... TS-2246122 ...Button Head Socket Screw ...

31Cast Iron Wings Index No. Part No. Description Size Qty 1 ... JPS10TS-501 ...Cast Iron Wing...

32Electrical Connections

4 Warning 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings poste

5 19. Provide for adequate space surrounding work area and non-glare, overhead lighting. 20. Keep the floor around the machine clean and free of sc

6 The most common accidents among table saw users, according to statistics, can be linked to kickback, the high-speed expulsion of material from the

7 Features Figure 1 (mobile base purchased separately) Specifications Model Number ... JPS-1

8 Definitions and Terminology Arbor: Metal shaft that connects the drive mechanism to the blade. Bevel Edge Cut: Tilt of the saw arbor and blade bet

9 Shipping Contents Carton Contents (see Figure 2) 1 ea Table Saw (not shown) 1 ea Blade (not shown) 1 ea Extension Wing – Left (A) 1 ea Extensio