Jet Tools 16-32 Plus Instrukcja Użytkownika

Operating Instructions and Parts Manual Drum Sander Model 16-32 Plus shown with optional casters (98-0130) and infeed/outfeed tables (98-1601)

10Assembling the Sander Tools Required for Assembly (not provided): Ratchet wrench with extension 7/16”, 9/16” and 1/2” sockets 9/16” open-end wrench

11 IMPORTANT: The conveyor belt has been over-tensioned for shipping purposes. It must be re-tensioned before operating the sander! See “Conveyor Bel

12Dust Collection Dust collection is mandatory for a safe work environment and extended abrasive life. The 16-32 Plus is equipped with a 4” dust coll

135. Mark the trailing end of the strip where it crosses the right (inboard) end of the drum (Figure 13). 6. Remove the abrasive strip from the dr

14Grounding Instructions Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be

15Extension Cords If an extension cord is necessary, make sure the cord rating is suitable for the amperage listed on the machine's motor plate.

16Dust Cover Latch The dust cover latch prevents the dust cover from accidentally opening. To release the latch, press inward on the dust cover knob

173. Remove the four bolts attaching conveyor assembly to base. Lift up and slide conveyor out to the side of the machine. 4. Set conveyor on motor

18Fine-Tuning Drum Alignment (for sanding boards wider than the drum) NOTE: Perform this alignment after you are familiar with sander operation. This

194. Loosen set screws on collar (Figure 28). 5. Slide collar upward against housing so that all vertical free-play of height adjustment screw is e

2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Serv

201. Repeat “Tension Roller Alignment” except raise the sanding drum only 1/4 turn of the height adjustment handle. 2. If both tension rollers are

21Multiple-Piece Sanding Runs When abrasive planing (or thickness sanding) a run of similar pieces that you want to have the same thickness, it is be

22Tracker Kit (98-0080) Trackers dramatically reduce tracking adjust-ments of conveyor belts. They are already installed on your sander. The followin

23Maintenance Before doing maintenance on the machine, disconnect it from the electrical supply by pulling out the plug or switching off the main sw

24Trouble Probable Cause Remedy Conveyor rollers run intermittently. Shaft coupling loose. Align shaft flats of gear motor and drive roller, and tig

25Abrasives The abrasive material you choose will have a substantial effect on the performance of your sander. Variations in paper type, weight, coat

26Optional Accessories 61-1012 Poly Conveyor Belt 98-0130 Locking Casters, set of 4 98-1601 Infeed/Outfeed Tables 80-2900 Elbow, 90° for 2.5” dust

27Parts List: Stand Assembly Index No. Part No. Description Size Qty 1A...40-4040... Left Leg ...

28Conveyor and Motor Assembly

29Parts List: Conveyor and Motor Assembly Index No. Part No. Description Size Qty 1...3237359... Gear Motor...

3 Table of Contents Table of Contents ...

30Drum Head Assembly

31Parts List: Drum Head Assembly Index No. Part No. Description Size Qty 34...70-4101... Motor...

3290...10-4007-10... Slotted Round Head Screw... 1/4”-20x5/8” ...3 91...11-1

33Electrical Connections

34NOTES

35

36 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com

4 Warning 1. Read and understand this entire manual before attempting assembly or operation. 2. Read and understand the warnings posted on the mac

5 blahblahblah 21. Make your workshop child proof with padlocks, master switches or by removing starter keys. 22. Give your work undivided attention

6 Introduction This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures for a JET Model 16-32 Plus Drum Sande

7 Features and Terminology The illustration below shows the major components and features of the 16-32 Plus Sander. These are referenced throughout t

8 Unpacking Open boxes and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any shippi

9 Assembling the Stand (Refer to Figure 4. If further clarification is needed, consult the parts breakdown on page 28.) Tools required for Stand asse