Jet Tools SuperSaw JWSS-10CS Instrukcja Użytkownika

Operating Instructions and Parts Manual SuperSaw Model: JWSS-10CS WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No. M-7087

10Assembly Unpacking and Clean-Up Do not connect the table saw to the power source until assembly has been completed! Failure to comply may cause se

11Mounting Rails Hardware: Front Rail, Rear Rail, (4) M8x16 Socket Head Cap Screws, (4) M8 Flat Washers, (4) Lock Washers, (2) 1/4-20 x 1-1/2 Hex Ca

12Miter Gauge for Left Extension Wing Hardware: Miter Gauge Tools: Cross Point Screw Driver, Square 1. Change the angle on the miter gauge by loos

13The support plate underneath the sliding table (Figure 10) has an inner tab (A) and an outer tab (B). When placing the table onto the leveling bra

14Sliding Table Miter Gauge Hardware: Miter Gauge, Fence, (2) Handles, Stop, Fence Bar, Indicator Bar, Bushing, Bracket Clamp Assembly & (2) Ha

15Mounting the Switch Assembly Hardware: (2) 1/4x1/2 Hex Cap Screws, (2) 1/4 Lock Washers, (2) 1/4 Flat Washers. Tool: 4mm Hex Wrench Referring to F

16table, until it is level with the saw table (Figure 17). As one part of the edge becomes level with the table, tighten the clamp on that side. Th

17slot (A. Fig. 21), orient the guide tube (B) with respect to the rail (C) as shown in Figure 21. If your left table wing is the sliding table type

184. Raise or lower two nylon adjustment screws (A, Fig. 27) the same number of turns until the space between the bottom of the fence and the table

19Installing the Blade When installing or changing saw blade, always disconnect saw from power source! Failure to comply may cause serious injury!

2Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Servi

20Blade Guard Assembly Hardware: Blade Guard Assembly, Splitter Guard Assembly Tools: 12mm Wrench, 17mm Wrench or Adjustable Wrench, 3mm Hex Wrench

21Hooks for Miter Gauge and Fence Hardware: (2) Miter Gauge Hooks, (2) Fence Hooks, (4) M8x16 Carriage Bolts, (4) M8 Flat Washers, (4) M8 Lock Washe

22Grounding Instructions This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakd

23 Adjustments Blade Alignment Tools: 8mm Hex Wrench, Combination Square & Marker Blade alignment with the miter slot is adjusted at the factory

24 Adjusting 45° and 90° Positive Stops The stops have been adjusted at the factory. After a period of use, or, after moving the saw to another locat

25 Wear Adjustment in Raising Mechanism As the worm gear wears with time you may notice a little play in the handwheel. To adjust for wear in the ra

26 Changing Poly V-Belt Make all machine adjustments or maintenance with the machine unplugged from the power source. Failure to comply may cause se

27 Maintenance General Maintenance Cabinet and Motor: Keep the inside of the cabinet clear of sawdust and wood chips. Vacuum out the inside of the

28 Troubleshooting Trouble Possible Cause Solution Saw stops or will not start 1. Overload tripped 2. Saw unplugged from wall or motor 3. Fuse blo

29 Parts XACTA Fence II Homeshop 30/52 Fence Assembly Index No. Part No. Description Size Qty 1 ...HF2-101 ...Left Si

3Table of Contents Warranty and Service...

30 Cabinet Assembly Index No. Part No. Description Size Qty 1 ...JWSS10CS-01...Cabinet...

31 Guard Assembly Index No. Part No. Description Size Qty 1 ...200321 ...Support Arm...

32 Table Assembly Index No. Part No. Description Size Qty 1 ...TS-1550061 ...Flat Washer...

33 Table Assembly Index No. Part No. Description Size Qty 58f ...200353 ...Switch Bracket ...

34 Table Assembly

35 Sliding Table Assembly Index No. Part No. Description Size Qty 1 ...200364 ...Sliding Table ...

36 Sliding Table Assembly Index No. Part No. Description Size Qty 57 ...200374 ...90° Adjustable Plate...

37 Sliding Table Assembly

38 Rail Assembly Index No. Part No. Description Size Qty ...708783Z...Rail Assembly - Standard (30”) ...

39 Rail Assembly

4Troubleshooting ...

40 Motor & Trunnion Parts List Index No. Part No. Description Size Qty 1 ...200310 ...Rear Trunnion Bracket...

41 Motor & Trunnion Parts List Index No. Part No. Description Size Qty 51 ...200404 ...Handle...

42 Motor & Trunnion Assembly

43 Wiring Diagrams 115V Wiring

44 230V Wiring WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.com

5 Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on t

6 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx 21. Provide for adequate space surrounding work area and non-glare, overhead lightin

7 The most common accidents among table saw users, according to statistics, can be linked to kickback, the high-speed expulsion of material from the

8 Read and understand the entire contents of this manual before attempting assembly or operation! Failure to comply may cause serious injury Contents

9Left Wing Extension Box (optional accessory) 1 Left Wing Extension w/Miter Slot 1 Miter Gauge 1 Miter Gauge Bar 1 Miter Gauge Handle 1 Miter Gauge