Jet-tools JJ-6CSDX Instrukcja Użytkownika Strona 1

Operating Instructions and Parts Manual Woodworking Jointer Models: JJ-6CSX, JJ-6CSDX WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123

10Installing Fence to Bed Referring to Figure 3: 1. Take the lock handle (E), flat washer (F), and lock nut (G) from the carton. 2. Place the fence

11Installing Belt Guard Referring to Figure 6: 1. Place the belt guard (A) over the opening in the stand. 2. Line up the holes in the stand with th

Electrical Grounding Instructions This jointer must be grounded while in use to protect the operator from electric shock. In the event of a malfunctio

13 Extension Cords Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the cu

14 Fence Stop Adjustments Periodically check the 90° and 45° backward (135°) tilt accuracy of the fence with an angle measuring device, such as an ad

15 Infeed Table Depth Stop Referring to Figure 17: The infeed table depth stop (A) limits the depth of a cut (set by adjusting the infeed table hand

16 Setting Cutterhead Knives (JJ-6CSX) Cutterhead knives are dangerously sharp! Use extreme caution when inspecting, removing, sharpening or replac

17 Replacing Knives (JJ-6CSX) Planer knives are dangerously sharp. Use extreme caution when inspecting, removing, sharpening, or replacing knives i

18 Outfeed Table Adjustment When you receive the jointer, the knives have been pre-set at the factory. However, the height and parallelism of the kni

19 Setting Cutterhead Knives (JJ-6CSDX) Note: Before setting knives for model JJ-6CSDX Jointer, the Outfeed Table Adjustment should be done to ensure

2This manual has been prepared for the owner and operators of JJ-6CSX and JJ-6CSDX Woodworking Jointers. Its purpose, aside from machine operation,

20 Replacing Knives (JJ-6CSDX) Planer knives are dangerously sharp. Use extreme caution when inspecting, removing, sharpening, or replacing knives.

21 Determining Correct Table Height When you receive the jointer, the knives have been pre-set at the factory. However, the height and parallelism of

22 Operating Controls 1. Hand Wheel for Outfeed Table 2. Outfeed Table 3. Fence 4. Fence Adjustment Handle 5. Cutter Guard 6. Infeed Table 7. Han

23 Hand Placement Never pass hands directly over the cutterhead. At the start of the cut, the left hand holds the workpiece firmly against the infee

24 Rabbeting A rabbet is a groove cut along the edge of a board. See Figure 37. The width and thickness of the wood to be rabbeted depends upon the w

25 Beveling To cut a bevel, lock the fence at the required angle and run the work piece across the knives while keeping it firmly against the fence a

26 Cutterhead Removal The entire cutterhead assembly may be removed for cleaning or for bearing and blade replacement. Some woodworkers keep a spare

27 13. To re-install the cutterhead, reverse the above steps. Note: Make sure that the fence base casting is level with the Outfeed table when securi

28 Troubleshooting Mechanical and Electrical Problems Trouble Probable Cause Remedy No incoming power. Verify unit is connected to power, on-button

29 Trouble Probable Cause Remedy Machine will not start/restart or repeatedly trips circuit breaker or blows fuses. On/off switch fail

3Table of Contents Warranty...

30 Fence – Parts All Models Index No. Part No. Description Size Qty. ...JEJ-FW ...Fence Assembly Complete (JJ-6CSX

31 Fence – Assembly All Models

32 Stand – Parts All Models Index No. Part No. Description Size Qty. 1 ... JI-Y01W ...Stand Body...

33 Stand – Parts and Assembly All Models 45 ...TS-0561031 ...Hex Nut ...

34 Bed – Parts All Models Index No. Part No. Description Size Qty. 1 ... JI-T01W ...Base ...

35 54 ...5F-H051 ...Rivet ... ...

36 Cutterhead – Parts and Assembly JJ-6CSX Index No. Part No. Description Size Qty. ...JEE-C01A ...Cutterhead Assembly

37 Cutterhead – Parts and Assembly JJ-6CSDX Index No. Part No. Description Size Qty. ...JJ6CSDX-CA ...Cutterhead Assembly (

38 Wiring Diagram – All Models WHITEBLACKBLACKWHITEGREENGREENGROUND 300MFD 125 VAC ELECTRICAL SCHEMATIC - 115V RED YELLOW BLACK

39 Notes

4 Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings poste

40 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com

5 20. Keep visitors a safe distance from the work area. Keep children away. 21. Make your workshop child proof with padlocks, master switches or b

6 39. Move the hands in an alternate motion from back to front as the work continues through the cut. Never pass the hands directly over the cutter

7Introduction This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures for\ Models JJ-6CSX and JJ-6CSDX Joint

8Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discar

9Assembly Unpacking and Cleanup 1. Carefully finish removing all contents from both shipping cartons. Compare contents of the shipping cartons with